13. Bumpers may be cut to remove sharp edges. No

extra reinforcements (bolts, washers, etc) chain around bumpers may be welded or bolted to bumper shock to keep bumper from falling off. Chains may not be heavier than 3/8" 3 links must be free from welds, max 3 links welded to frame on each end. Front and rear bumper height to be 22" Max. to bottom of bumper, checked in three places. Maximum of 1/4" plating may be used no larger than 6"X6" welded onto the bumper shock plate if a different make bumper is being used on car only one (1) plate is permitted. Face bar cannot be welded to reinforcement RERUNS: BUMPER HEIGHT MAX OF 24" CHECKED IN THREE PLACES NO EXPOSED FRAME RAILS, NO PROTRUDING BUMPER SHOCKS WILL BE PERMITTED. Bumpers may be welded on, if bumper shock is left in original position. bumper may still be welded on. If bumper shock is removed you can weld the bumper to the frame rail. One six by six plate can be added to bumper. no extra reinforcement to be added to frame rail. Cars cannot have bumper shock inside frame rails if bumper is welded straight to frame rail. NO EXCEPTIONS! YOU WILL NOT RUN

14. Battery mounted to floor (not in seat) must be separated at least 5 feet from relocated gas can and secured firmly in place. Batteryshould be covered. Only 1 battery is permitted, any size (i.e. 12 or 14 volt, - NO 24 volt batteries allowed).

15. Relocated gas container must be secured firmly behind drivers seat in metal approved cans only (boat cans will be accepted). Compact Class only, may relocate tank inside car but must have a kill switch on the fuel pump. NO PLASTIC CANS

16. Radiators can not be relocated. May be banded (two bands maximum) to core support vertically or horizontally. chrysler radiatormounting bracket to be 3"x3"x1/4"x6"long Max.To be mounted to core support.OVERFLOW must be pointed toward ground& attached to car so it will not spray forward. No expandable foam. WATER ONLY. No antifeeze (crowd safety)

radiators may have window screen to protect from flying objects or mud. Homemade grates or grids will not be permitted. No homemade cover plates. Home made cooling systems may not touch any part of frame or metal on car. Attached to engine only. Radiators can only be mounted to core support.

17. All cooling systems must be under the hood. No cooling systems inside the car (driver compartment). Transmisson cooler may be relocated behind front seat. Tranny lines must be covered

 Air cleaners will be mandatory.

18. Coil springs may be welded, wired, banded, bolted or chained (bottom only) to rear end! No coils inside of coils. Spacers will be allowed in coil springs to max. 22" bumper height.

19. Brakes must work. No deliberate hitting of arena tires for braking purposes.

20. Skid plates may be welded on oil pan and transmission pan (separately), no more than 1" wider than the part

21. Must cut 2 (two) holes , 12 " minimum in trunk for inspection

Maxium of (12) 3/8 "bolts allowed around holes each hole for a maximum of 12 bolts total. Removal from inspection line if not cut out.

22. STAY IN CAR AND DO NOT LOOSEN SAFETY BELT UNTIL EVENT IS STOPPED OR OVER.

23. After second fire in same auto, in same event, the car will be disqualified.

24. No deliberate hitting of drivers' door.  Do not use drivers door as a shield

25. No teamwork (double-teaming). If you are caught teaming up, one or both drivers will be disqualified.

26.NO fresh PAINTING OF INSIDE OF CARS!!! No undercoating underneath, inside or on frame

27.Inspections will close at 7:30, DRIVERS MEETING AT 7:40

DERBIES BEGIN AT 8:00 P.M., CARS WILL NOT BE ACCEPTED ON GROUNDS AFTER 7:30 P.M. DRIVERS MUST BE WITH THEIR CAR NO LATER THAN 7:30 P.M.NO EXCEPTIONS.

28. Exhaust coming out of hoods must be pointed straight up. If exhaust is considered to be pointed in a direction of danger to the fans or other drivers the car will be disqualified.

29. The officials reserve the right to re-inspect cars at any time during the event.

30. Leaf springs: All cars with leaf may have 9 springs on each side including the main springs may be 5/16" thick max. (if 5/16 wrench WILL NOT fit over spring YOU WILL NOT RUN) max 2 3/4 " wide spring must have min. of 1" stair step starting from the eyebolt. All springs must be mounted under the main axel tube. Springs may be clamped with factory tin clamps only, 2 behind axle and one in front per side. (no duct tape ) Home made leaf springs not permitted. Only one (1) main leaf, all springs must be under the main. Minimum 12" height to bottom of bumper.

May use homemade leaf springs (ONLY on the "Tribute to the Classics" night cars ONLY ) No welding of leafs together.

31. Frames: Hybrid frames not permitted. Must be factory frame, same year, same model as car if repairs are neccesary.

32. Carb protector & distributor protector are allowed. Cannot touch frame in any way. Can only attach to top of motor, or intake or heads. Motor dradles are not permitted.

New Rule: Maximum 5 Bolt rearends on cars.

Contact Demo CHAIRMAN

Aaron Slezak at tslezak724@windstream.net

SAFETY RULES 1 - 12 ON PREVIOUS PAGE...CLICK HERE 

|  Demos  |  Prizes  |   Requirements  |  Schedule  |
|  Safety Rules pg1  |  Safety Rules pg2  |  compact rules-classics   |team derby /truck rules